Skip to content

Are You Using Bulk 55 Gallon Drums Of Brake Cleaner? 

Are You Using Bulk 55 Gallon Drums Of Brake Cleaner? 

If so, you need to read this. To save on costs, many service departments are purchasing flammable liquids such as brake cleaner, lacquer thinner, gasoline, and other flammable liquids in bulk 55-gallon drums.  While this may make economic sense, you may have to spend a bit more upfront to comply with flammable liquid storage regulations.

Most formulas of brake cleaner, lacquer thinner, and gasoline are found to be flammable, meaning that they carry a flashpoint of less than 100°F.  The “flashpoint” is the minimum temperature at which a liquid gives off vapor in sufficient concentration to form an ignitable mixture with air near the surface of the liquid.  Meaning that sparks will ignite the vapors before it gets to the liquid causing fire or explosion.

The OSHA classifications are:

  • Category 1 liquids have a flashpoint below 73 °F and have a boiling point at or below 95 °F.
  • Category 2 liquids have a flashpoint below 73.4 °F and have a boiling point above 95 °F.
  • Category 3 liquids have a flashpoint at or above 73.4 °F and at or below 140 °F.
  • Category 4 liquids have a flashpoint above 140 °F and at or below 199.4 °F.

Why does the flashpoint of my bulk products matter?

NFPA 30 and OSHA have regulations regarding the maximum amount of flammable liquids that may be stored without requiring the use of a flammable storage room or cabinet.

Code of Federal Regulations (CFR) 29 CFR 1910.106(e)(2)(ii)[b] states the following:

The quantity of liquid that may be stored without requiring the use of an inside storage room or flammables storage cabinets in any one fire area of a building cannot exceed:

  • 25 gallons of Category 1 liquids in containers
  • 120 gallons of Category 2, 3, or 4 liquids in containers
  • 660 gallons of Category 2, 3, or 4 liquids in a single portable tank

A drum is classified as a container and not a tank.

This means if you have brake cleaner stored in a 55-gallon drum that meets the classification of a Category 1 Flammable liquid then you will need to keep the drum in one of these places:

  • a flammable liquid storage room (a storage room has specific requirements),
  • flammable liquid storage cabinet, or
  • outside away from the building.

If your brake cleaner falls into Category 2, 3, or 4, then you may keep 2-55 gallon drums onsite in the service department.

Where can I find the flashpoint of flammable classification of my bulk products?

There are two main ways to find this info:

  • contacting the manufacturer, or
  • reviewing the SDS (Safety Data Sheet) for the product

You can find the flashpoint in Section 5 – Fire Fighting Measures or Section 9 – Physical and Chemical Properties.  You will find the boiling point under Section 9.

This will help you to determine which class of flammable liquid your brake clean will fall into.

I have a Category 1 flammable liquid 55-gallon drum in my shop. What do I need to do?

If you have a Category 1 55 gallon drum stored by a wall in the service department, this is most likely a regulation violation.   To correct this, you may consider the following:

  • Use a non-flammable liquid method of brake cleaning
  • Make a switch to a Category 2, 3, or 4 brake cleaner
  • Switch to aerosol cans
  • Reduce the size of the drums kept in the shop
  • Purchase a flammable cabinet for the drum
  • Store the drum in a flammable liquid storage room
  • Store the drum outside away from the building

Much like how there are rules and regulations concerning storing brake cleaner in large drums, there are also regulations about storing other flammable liquids. To ensure that you’re compliant, implement the following at your shop:

Grounding

Flammable liquids dispensed using a metal pump must have an electrical ground installed on the pump or tap.  This can be accomplished by connecting a copper wire from the tap to a grounded object.

Keep in mind that not all structures will provide a suitable ground.  Putting a screw into a concrete wall would not be a recommended ground.  The ground wire should be connected to a nearby water pipe, electrical conduit, or an actual ground rod.

Bonding

Bonding is not the same as grounding.  Bonding is the process of connecting the container dispensing the flammable liquid to the container being filled, typically by a copper wire. Bonding is designed to eliminate an electrostatic spark from reaching the flammable vapors.

Category 1, 2, and 3 liquids with a flashpoint below 100 °F must have a bonded connection when dispensing from one metal container to another, such as a 55-gallon drum to a pressurized spray can.  This can be accomplished by making a separate bond wire available at the filling area.  Make sure you train your employees to attach the bond wire during the filling process.

Flammable Spray Areas

Using brake cleaner in a pressurized spray can be interpreted as a spray area, which means that surrounding ignition sources need to be eliminated.

29 CFR Subpart 1910.107(a)(2) defines a spray area:

Spray Area: Any area in which dangerous quantities of flammable vapors or mists, or combustible residues, dusts, or deposits are present due to the operation of spraying processes.

29 CFR Subpart 1910.107(c)(2) states the following:

There shall be no open flame or spark-producing equipment in any spraying area nor within 20 feet thereof unless separated by a partition.

The average mid-sized sedan is 15 feet in length.  Due to these regulations above, technicians must make sure to delay the spraying of the brake cleaner until all torching, welding, and any other sources of ignition (including vehicle engine ignition) are eliminated or off in the immediate and surrounding bays.

Let’s save the sparks until the 4th of July, and the flames for roasting marshmallows.

If you have questions or need further assistance in the topic of flammable liquid use and storage we’re here to help. KPA offers environmental risk management services to assist you in managing chemicals and hazardous waste at your facilities. We help you document procedural compliance and provide guidance on minimizing waste generation and appropriately managing and disposing of wastes. Our compliance inspections, plan development, and permitting assistance will help you resolve your environmental compliance challenges.

Contact us to learn more.

About The Author

Glorianna Reeser

More by this Author >
Back To Top